Tips From the Moving Company Pros: Ways To Move a Pinball Maker



With pinball making a big renewal throughout the country, Gentle Giant desires to make certain that these classic, gorgeous makers remain damage-free while being transported. Oh, and we want the individuals moving them to be safe, too.

At very first glance, pinball machines can appear daunting to move due to the fact that of their size, fragility, and weight. Fortunately, our proficient Giants have a couple of tricks up their sleeves to ensure your pinball is moved with ease.
Folding Down the Headbox

The majority of contemporary pinballs (made in the last Twenty Years or so) have a hinge system which allows the headbox to be folded down. Early pinball devices had their headboxes bolted on, utilizing either 2 or 4 bolts. All Electro-Mechanical pinballs use this system, along with the early Solid State devices.

Later on makers have hinges and use a latching system to keep the headbox upright. There may likewise be 2 bolts inside as included safety, in case the latch is broken or unintentionally un-latched.
Electro-Mechanical Pinballs

For Electro-Mechanical pinball devices, you have to get rid of the headbox rear access panel to get to the bolts and plugs inside. Normally this panel has a lock on it to keep it in location, however with time the key may have been lost. Frequently, there is a screw keeping this panel in location.

As soon as within, remove the bolts and unplug the large ports that have electrical wiring decreasing into the maker. You might want to label these connectors to put them back in the best spot, however they must be various sizes, making it hard to plug back incorrectly.

You can now remove the headbox completely, or fold the headbox down onto the playfield glass. Ensure you utilize some foam, heavy cardboard, or blankets to safeguard the headbox from rubbing on the cabinet. Foam is best, as it will assist keep the back glass in location.
Early Strong State Pinballs

For early Solid State Pinballs, you will need to remove the back glass. There is a lock located on the headbox in one of three places: the left-hand side at the top, right-hand side at the leading or on top of the headbox in the center.

Once unlocked, remove the back glass by lifting it up using the lift channel (at the bottom of the glass), and after that pull it out from the bottom.

Then, open the back box light panel by raising the lock situated on either the left-hand side or right-hand side. The panel can now swing out to you, and give you access to the circuit boards, plugs, and the bolts. Some Gottlieb pinballs require you to raise the lamp panel in order to swing it open.

Now that you are inside, you can eliminate the bolts, and any plugs that have wires going down into the device. You might wish to identify these plugs to put them back in the ideal area. You might not require to get rid of the plugs, as the wiring should be long enough to allow the headbox to be folded down.

At this point, you can secure the light panel and change the back glass.
Modern Strong State Pinballs

For Data East, Sega, and Stern Modern pinballs, there is a turnable lock system situated at the back of the headbox. Utilizing the provided secret, turn the lock 90 ° counter-clockwise.

For Williams, Bally, and Gottlieb, you can quickly unlatch the back box at the back of the maker. This is a basic setup and needs no tools.

If you can now fold down the head box onto the cabinet, you're done. Make sure you use some foam, heavy cardboard, or blankets to protect the headbox from rubbing on the cabinet. Foam is best, as it will also help keep the back glass in place.

If you can not fold the head box down, then you need to get inside. There is a lock located at the top of the back glass in the. Use the supplied key to unlock, and eliminate the back glass by lifting it up from the bottom, and after that pulling it out from the bottom.

Next, you will have to eliminate the screen panel. You can do this by lifting it up and out. And finally, open the lamp panel. There will be a latch located on either the right-hand or left-hand side. (Some newer Williams and Bally pinballs do not have a separate amp panel, it belongs to the back glass panel. And later Sega and Stern pinballs use a fluorescent tube for the back glass lighting).

Remove the two bolts, put the back box back together, and fold down the head box onto the cabinet. Make sure you utilize some foam, heavy cardboard, or blankets to secure the headbox from rubbing on the cabinet. Foam is best, as it will likewise assist keep the back glass in location.
Getting rid of the Legs.

Pinball Maker legs are kept in location by 8 bolts. They will be either 5/8 inch or see here 9/16 inch heads. The contemporary pinballs have captive nuts or threaded plates inside for the bolts to screw into. These bolts can be eliminated, and the legs will come off.

These threaded plates and captive nuts can be harmed, and the usage of additional nuts may have been required. If this is the case, you will have to open up the front door of the pinball, slide out the playfield glass, and raise the playfield.

With the front door (coin door) open, move the lock down bar lock throughout and eliminate the lock down bar. Then move out the playfield glass, and put in a safe place. Next, lift up the playfield by placing your hand where the ball drains pipes, and raise the playfield up.

You must now have access to any nuts that might have been used. When any nuts have been removed, change the playfield glass and lock down bar, and lock the front door.

Make certain to mark or keep in mind which legs are for the front and back, as they will be changed in a different way to fit.
Loading the Pinball.

You are now ready to carry your pinball maker. Prior to you pack it, ensure you remove the pinballs so they don't bounce around during transportation.

If you are moving the pinball using a van or SUV, it may be much easier to get rid of the legs simply prior to packing the machine. Grab a good friend to assist and have one of you supporting the pinball, while the other removes the front legs.

Make certain you strap the pinball in, as you do not desire it moving if you have to stop unexpectedly!

For Electro-Mechanical pinball devices, you need to get rid of the headbox rear access panel to gain access to the bolts and plugs within. (Some newer Williams and Bally pinballs do not have a different amp panel, it is part of the back glass panel. And later on Sega and Stern pinballs use a fluorescent tube for the back glass lighting).

If you are moving the pinball utilizing a van or SUV, it might be simpler to eliminate the legs just prior to loading the maker. Get a buddy to have and assist one of you supporting the pinball, while the other gets rid of the front legs.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Comments on “Tips From the Moving Company Pros: Ways To Move a Pinball Maker”

Leave a Reply

Gravatar